www.Usenet.com
www.Usenet.com
| <-- __Chronological__ --> | <-- __Thread__ --> |
Archive-name: apple2/faq/part9
Posting-Frequency: monthly
Last-modified: 2003/10/1
URL: http://home.swbell.net/rubywand/A2FAQs1START.html
The comp.sys.apple2 Usenet newsgroup Apple II FAQs originate from
the Ground Apple II archive, 1997-2003. Administrator: Steve Nelson
Csa2 FAQs-on-Ground ref: Csa2FDRIVE.txt rev067 October 2003
Floppy Disk Drives
001- How do I add a write-protect On-Off switch?
002- How do I add external speed adjustment to my Disk ][ drive?
003- How can I adjust my 5.25" drive for optimum performance?
004- How do I clean my disk drive R/W head(s)?
005- What is the pin-out for a duodisk drive connecting cable?
006- What DuoDisk mods are necessary?
007- Will a Duodisk function correctly on my ROM 3 GS?
008- How do I fix a false Write Protect?
009- My 3.5 Disk Drives don't work! What should I try?
010- I added SCSI; now, my 3.5" drives often fail to work. Why?
011- Both of my Disk ]['s come on when booting! Is there a fix?
012- In connecting a Disk II I misaligned the connectors. A fix?
013- A sound like a shotgun going off came from my drive. A fix?
014- Uni-disk and Laser drives: neither works with my IIc. Why?
015- How do I replace a 3.5" drive mechanism with one from a Mac?
016- I have one 5.25" drive. Sys6 shows two icons!? Is there a fix?
017- How can I tell a 13 from a 16-sector Disk ][ controller card?
018- Can a Disk ][ Drive be used on a IIc or GS smartport?
019- How do I install a bi-color LED R/W indicator in my Disk ][?
020- What's the scoop on the 3.5" High Density drive?
021- What is a "UniDisk"?
022- What is a "RAM disk"; and, how do I create one on my IIgs?
023- Which 3.5" drive/interface combinations work on a IIe?
024- How can I boot from my /RAM5 RAM disk?
025- My 5.25" drive ruins every disk I insert. How can I fix it?
From: Stephen Buggie
001- How do I add a write-protect On-Off switch to my Disk ][ drive?
Adding an Auto/Manual Write-Protect (A/MWP) Switch
Often, as when doing copying, it is useful to be able to guarantee that a
diskette is Write-Protected whether or not the side is notched. Other times, it is
convenient to defeat Write Protection-- for example, when you wish to write to a
diskette side which is not notched. And, naturally, you also want a setting which
permits Normal, notch-controlled, Write-Protect.
Based upon a circuit suggested by David Wilson (Australia), the A/MWP enhancement
offers full user control of Write Protect. The switch's three positions are
Normal: a diskette side must be notched to permit writing.
Protect ON: Writing is prohibited regardless of notching.
Protect OFF: Writing is allowed regardless of notching.
A/MWP Step-by-Step
Unplug the drive from the disk controller and remove the case.
Drill a mounting hole. This can be at a convenient spot in the back or in the plastic
front panel. On the front, a good spot is at the lower left, above and to the left of
the "in use" LED. Another open spot is at the upper right in the space just above the
diskette slot; but, we're saving this place for Part 2's enhancement. (You can't use
the lower right, of course, because this would mess up the "Apple" logo!)
Cut three wires (Brown, Black, and White) long enough to run from the mounting point
to the Large Connector plugged onto the back, middle of the Disk ][ circuit board.
Solder the leads to a Single-Pole Triple-Throw mini toggle Switch: Brown to center,
White to one end, Black to other end. Twist the leads or encase them in tubing.
Mount the Switch. Normally, the Switch handle will point ...
o- in the Black lead direction for "Normal" (center and White connected)
o- at Center for "Protect ON" (no connection).
o- in the White lead direction for "Protect OFF" (center and Black connected).
Mounting the switch with the Black lead on top is recommended because it is easy to
remember that Up = Normal. Route the leads to the area next to the Large Connector.
(Make sure no wires will get in the way of an inserted diskette.)
Locate the Brown and Black leads coming from the Notch Detect micro-switch. The leads
are the Brown (bottom) and Black (top) pair near the right end of the Large Connector
(as viewed from the front of the drive).
Cut the Notch Detect micro-switch leads about 1" away from the Large Connector.
Connect the Black Notch Detect, Black Large Connector, and Black Switch leads (i.e.
strip ends, solder, and cover in heat-shrink tubing or tape).
Connect the Brown Notch Detect lead to the White Switch lead.
Connect the Brown Large Connector lead to the Brown Switch lead.
Viola! Now you're ready to replace the cover, plug in the drive, and try out your
A/MWP enhanced Disk ][.
----------------------------
From: Ed Eastman
Most of the time what you want to be able to do with a Write Protect modification
is turn On Write Enable when a disk is not notched. That is what this mod for does.
Details relate to the 5.25" Unidisk but the method will also work with other Apple II
5.25" drives.
The way the write protect sensor works on newer drives is that an LED on one side
shines on a phototransistor (the sensor) on the other side. When there is a notch in
the diskette you insert, light passes through the gap and the sensor 'closes' to
complete the Write Enable circuit.
What we will do is give the Write Enable circuit an alternate enable option using
an On/Off switch. A mini toggle switch is okay; but, I like to use a small
normally-open momentary contact pushbutton switch from Radio Shack. It's compact,
looks nice, and pressing the button for the few seconds usually required for a file,
etc. write is no problem.
I normally mount the switch in the upper left part of the face plate, opposite
the light to balance the look. Drill a hole a little smaller than required and use
scissors or a larger drill to taper the hold to just where you can screw in the
switch.
Before soldering on leads and mounting the switch, decide where you want to make
the connections. You can locate the output leads from the sensor and splice one switch
lead to each; or, you can find the place on the circuit board where the sensor leads
go and connect there.
On a Unidisk you will see a large connector labeled "CN1" near the front. Pins 9
and 11 of CN1 are the write protect sensor connections. More convenient connection
points are the circuit board edge side of R12 and the wire at J29.
Solder on leads long enough to reach the connection points and screw in the
switch. On a Unidisk, connect one switch lead to the R12 point near the edge and one
to the wire at J29.
Now when you need to override write protect on an unnotched disk, you simply
press the button while writing. Go ahead and plug in the drive and give it a try.
____________________________
From: Stephen Buggie
002- How do I add an external speed adjustment to my Disk ][?
Reference: FAQs Resource file R006SPDKNOB.GIF
Adding a Speed Control Knob to your Disk ][ Drive
This article tells how to move speed adjustment from the Disk ]['s dark interior
to a handy front-panel location and how to "tune" the drive for optimal performance.
One drive-test software vendor states that Disk ][ is good for about 500 hours of
normal use between speed adjustments-- not exactly a strong argument for placing the
control on the front panel! On the other hand many of today's Disk ][ owners are
interested in applications which go beyond "normal use".
Some utilities (e.g. DiversiCopy II) report rotational speed during ongoing
applications; so, relocating the speed adjuster to the front panel is especially
helpful. Similarly, users who want to back up their old, copy-protected wares know
that ready access to speed control is essential.
Finally, there is no question that, whatever your applications, periodic speed
trimming will be required. When it is, you'll be very glad _your_ Disk ][ has a front
panel Speed Knob!
Adding Speed Knob
To install Speed Knob you will need a good quality, linear taper 5k Ohm
potentiometer, some wires, and a knob with a pointer mark or some other way to show
position (e.g. a ring of numbers). Most of the work, really, consists of opening the
drive and drilling a hole. There is no need to disconnect the drive from the
controller card.
1. Remove the 4 bottom bolts and slip off the case. Unscrew the 4 bottom bolts holding
the drive to the case bottom, and unplug the main ribbon cable. The drive can now be
moved to your work area.
2. Drill a hole properly sized and centered for mounting your 5k Ohm pot in the upper
right front panel.
3. Place the drive on its face and unscrew the 2 bolts which hold the small daughter
board to the drive. (Be ready to catch loose spacers, washers, etc..)
4. Turn the small board over to the bottom side. Locate and cut the traces going to
the mini-pot speed adjuster as shown in pic R006SPDKNOB.GIF.
5. Cut three wires, White, Gray, Black, long enough to reach from the board to the
front panel. Connect these to your 5k Ohm pot and to the small circuit board as shown
in pic R006SPDKNOB.GIF. (In case you cannot view the pic, what you're doing is
substituting the new pot for the mini-pot. )
6. Re-mount the daughter board. Mount the 5k Ohm pot. Install knob.
7. Bring the drive back to the computer. Slide it onto the case bottom plate,
reconnect main ribbon cable, replace bottom bolts, slide on and re-fasten case top.
You can use Copy II Plus, XPS, APEX, or one of several other utilities to set
speed (see next question). A good starting adjustment will be near the center of Speed
Knob's range. Once speed is adjusted, you can loosen and re-set the knob so that its
position indicates a "correct" speed setting.
----------------------------
003- How can I adjust my 5.25" drive for the best performance?
The typical 5.25" drive will run for months with no need for maintenance save an
occassional dusting or session with a head-cleaner disk. When adjustment is required,
it will usually be to fine-tune Speed or, less often, to set track centering.
If a 5.25" drive has difficuly reading diskettes, including those it created, and
head-cleaning does not help, then, the odds are it's time to adjust speed. If your
drive is a Disk ][ and does not have the external 'Speed Knob' mod, look for a small
hole on the lower right side near the back-- some owners add this hole to allow easy
access to the Speed Adjustment mini-pot screw. If there is no hole, you will need to
remove the case. (Remove bolts on bottom and slide out the drive through the front.)
On the 5.25" Apple 'Platinum Drive', the Speed Adjustment is accessed through a
small hole on the bottom of the drive near the front on the right side. Non-Apple
5.25" drives may place the Speed Adjustment almost anywhere. Look for a small hole
through which you can see a screw head. If you don't fine one, remove the case and
look for a mini-pot labeled "Speed" or something similar.
The most popular speed adjustment software utility is, probably, dear old Copy II
Plus. From the menu, just select "Verify", then "Drive Speed". Put a diskette into the
drive you want to adjust and, turning the Speed Knob (or min-pot shaft) use Copy II's
numeric speed display to zero-in on the 'magic' 200ms. number. (Standard Disk ][
rotation speed is 300 rpm, which comes out to be 0.2 seconds per revolution.)
Other speed adjustment utilities show an rpm number or a hires pointer. Whatever,
all speed check routines need to read AND write; so, you will usually need a "scratch
diskette" which you do not mind having over-written.
Track-center realignment is needed when a Disk ][ writes and reads its own disks
fine, but does not 'communicate' with many other Apple II 5.25" drives. It generates
disk errors when reading disks written by other drives and other drives have the same
problem with its diskettes.
CALL A.P.P.L.E's APTEST, now in the public domain, tests track-center alignment.
With this software, the user checks the alignment of the drive with disks regarded as
well aligned --- such as Apple diskware supplied with the computer or some
unprotected, original, commercial software diskette. (In a pinch, a diskette formatted
by any drive that has no problem reading most other diskettes should be okay.)
Basically, a track-centering test tries to step your head between two tracks of
the 'standard' diskette and read the tracks on either side. If the number of
successful reads from each track is about equal, the head is "centered" and your drive
is well-aligned with the standard diskette.
The test may indicate serious misalignment. ("Aha! That explains why my IIgs and
II+ have problems reading each other's diskettes!") Centering adjustment is done by
slightly repositioning the stepper motor (mounted on the underside of the drive). This
requires loosening the two bolts holding the stepper-motor, rotating it clockwise or
counter-clockwise, and retightening.
The adjustment/test process may require several repetitions. Each time, the
program will report "differential fractions". The smaller these numbers, the closer
you are to near perfect alignment with tracks on the diskette.
----------------------------
From: Rubywand
Suppose you have just one drive and it is so far out of adjustment that it will
not boot a speed adjustment utility diskette? In this case, you can remove the drive
cover, turn over the drive, and (probably) find that the drive has a strobe pattern on
the main pulley or flywheel.
Set a fluorescent light near the drive (or do the adjustment in a room with
fluorescent lighting). Get the drive spinning via power-on booting or a PR#6 and
adjust the speed for a stable pattern.
Note: If you live in a place which supplies 50Hz power and the drive is intended for
use in the U.S. or other country with 60Hz power, you may have to experiment with +
deviations in speed from a stable pattern.
____________________________
From: Rubywand
004- How do I clean my disk drive R/W head(s)?
The easiest way to clean a drive's R/W head(s) is with a Cleaner Diskette. This
is a diskette with a paper disk such as the 5.25" and 3.5" Cleaner Diskettes available
in Radio Shack's Disk Drive Head Cleaner Kits. These kits usually include "Cleaning
Fluid" (isopropyl alcohol), too.
The 5.25" Cleaner Diskette has panels you pop out to expose the cleaning surface.
Apple II 5.25" drives have a single head which contacts the disk from the bottom and a
pressure pad which presses against the top side. So, pop out the panel on the bottom
side of the Cleaner Diskette and leave the top panel in place. When cleaning, insert
the diskette with the bottom side facing down. This lets the paper disk rub against
the head and avoids wear on the pressure pad.
The 3.5" diskette has a small plastic panel you can snap out for cleaning
two-head drives. Since the standard 3.5" 800k Apple II drive has two heads, snap out
the panel so that both the top and bottom heads get wiped.
To clean your drive head(s), you sqirt a few drops of Cleaning Fluid onto the
Cleaner Diskette disk, insert it into the drive, and get the disk spinning for 20
seconds. (Booting the Cleaner Diskette is one way to get it spinning. If DOS or ProDOS
is installed, doing a CATALOG is another way. For example: CATALOG,S6,D2 would get
your 5.25" Drive 2 spinning.)
If you think it has been several months since the drive was last cleaned, repeat
the procedure-- i.e remove the Cleaner Diskette, add more fluid, etc.. As a rule, do
not let the disk spin more than 20 seconds for any cleaning cycle. This is especially
a concern with 3.5" drives where the heads are mounted on springs and much more
subject to snagging and being pulled out of alignment.
____________________________
From: Steve Jensen
005- I picked up an apple IIe and a duodisk drive at a thrift
store. Could someone describe the connecting cable?
I just checked the pinout on a Duodisk cable. The numbers for the pins are
inside the plug by the pins, but I'll draw them for you.
DB 19 looking at the end of the cable:
1 2 3 4 5 6 7 8 9 10
o o o o o o o o o o
o o o o o o o o o
11 12 13 14 15 16 17 18 19
DB 25 looking at the end of the cable: (x = no pin)
1 2 3 4 5 6 7 8 9 10 11 12 13
x o o o o o o o o o o o x
o o o o o o o o x o o x
14 15 16 17 18 19 20 21 22 23 24 25
Cable
DB 19 DB 25
1 2
2 4
3 9 & 21
4 10 & 14
5 23
6 7
7 19
8 20
9 8
10 12
11 15
12 16
13 17
14 18
15 5
16 24
17 11
18 3
19 6
____________________________
From: Steve Jensen and Jonathan Adams
006- What DuoDisk mods are necessary?
The following is excerpted from an info file from my old bbs ...
There are TWO modifications that should be made to Duodisk drives:
The First one was recommended by Apple several ago to solve occasional problems
with trashing diskettes. The solution is to remove 2 capacitors.
The Second modification is only required to solve a problem with daisy-chaining
on the GS Smartport, though the modified Duodisk will still work fine on older Apple
II's. It requires removing a resistor.
DUODISK MODIFICATION #1- REMOVAL OF TWO CAPACITORS
This mod should be done on ALL Duodisks, no matter whether they're used on //e's,
IIGS's, etc. The problem was that diskettes would sometimes be damaged when doing an
Open-Apple-CTL-Reset or when using disks with certain kinds of copy protection. The
mod was in an Apple dealer service bulletin several years ago for "analog board PN
676-[]101 or 676-[]102."
The Analog board is the one inside Drive 1 in the Duodisk. You may have to
unplug the cable near the back right of the board to see the board's model number.
Anyway, if you have the -101 or -102 board, just snip out Capacitors C29 and C30 at
board locations A1 and B1, respectively.
DUODISK MODIFICATION #2- REMOVAL OF A RESISTOR
This mod should be done for Duodisks used with a GS; otherwise, it is optional.
The problem is that the Duodisk draws just a little too much current when connected to
the GS Smartport. This can render other drives on the chain inoperable. Problems are
MOST likely to occur when the Duodisk is daisy-chained from a Unidisk 3.5 Drive.
Remove the top cover and turn the drive so that the identifying number will be at
the bottom left of the analog board. The number might read 676-[]101, 676-[]102 or
676-[]107. (ROM 3 GS users should check Q&A 007.)
If the I.D.# for the analog board is 676-[]101 or 676-[]102, use a pair of nippers and
cut out resistor R8 (located at position A2).
If the I.D.# for the analog board is 676-[]107, use a pair of nippers and cut out
resistor R39 (located at position C3).
----------------------------
From: Dave Althoff
There are two capacitors which must be clipped from the board on the DuoDisk
regardless of what machine you intend to use them on. Failure to do this can lead to
very nasty failures. For instance, some copy-protection schemes can cause the drive to
start writing unexpectedly-- say, during a re-boot-- thus trashing the disk without
regard to the write-protect switch.
----------------------------
From: Chet Gerhardt
I have done the capacitor removal mod with all DuoDisks I have sold and my own
DuoDisks. It is amazing that after all of this time most still have not had the mod
done.
____________________________
From: Steve Buggie
007- Will a Duodisk function correctly on my ROM 3 GS?
I have three Duodisks. The one connected to my flagship ROM 3 IIgs has had the
resistor and capacitors clipped out as recommended in a memo from Mitch Spector. It
works perfectly!
----------------------------
From: Rubywand
A Duodisk may not be entirely functional connected to the usual ROM 3 "Disk"
connector (i.e. the SmartPort). Users report that the system may not start up unless
a write-protected disk is inserted in the Duodisk. Apple, in Tech Library notes #5010
and #5434, mentions these reports and says that there is some code in the ROM 3 ROM
that does not handle the interface to a Duodisk properly. Apple's workaround is to
connect the Duodisk to a drive interface card instead of to the Smartport.
____________________________
From: John L. Graham
008- How do I fix a false Write Protect?
I recently ran into this problem with a Disk II. It insisted the disk was write
protected. I checked the write protect switch, but it was okay. I pulled all the chips
out of the analog board inside the drive, cleaned the contacts with a clean pencil
eraser (one was _really_ dirty, almost looked burnt) and re-installed them. Voila! The
problem went away.
____________________________
From: Rubywand
009- My 800K, 3.5 Disk Drive is no longer working on my IIGS.
When a disk is inserted the drive tries to read it and then
locks up the entire system forcing me to do a 3 finger reboot.
Any suggestions on where to start troubleshooting?
If you have a SCSI interface card plugged into your GS, you may have run into a
bug which seems to affect setting up of the diskette port. (See the next question and
answer.)
Try cleaning the heads using a Head Cleaner Diskette, such as a paper diskette +
cleaning solution kit from Radio Shack. (See Q&A 004.)
In a few rare cases, a drive may actually have globs of dust inside which end up
interferring with its operation. You can shine a flashlight into the slot to check for
a heavy dust buildup. The safest way to clean out dust is to open the case and the
drive and remove the dust. However, you can try inserting a small cheap plastic
artist's paintbrush (slightly dampened) into the slot and, with a flashlight,
_lightly_ sweeping around to pick up dust. ("Lightly" means you do not push or snag on
anything,
especially the R/W heads.) Blow into the slot and do another sweep with your brush.
If cleaning does not seem to help, try wiggling the drive cable while attempting
to CAT a known-good, unprotected diskette in the drive. If wiggling helps, you are
likely to have a bad cable or a GS plug with a loose connection to the motherboard.
Try formatting a diskette. A drive which can format and R/W diskettes it has
recently formatted but cannot read most other diskettes probably has heads which have
become misaligned.
Set your boot Slot to Slot 5 and try power-up booting a couple bootable ProDOS
diskettes known to be in good condition. If you can boot a variety of disketts,
including commercial game, etc. diskettes, the odds are pretty good that your drive is
okay.
A 3.5" drive that, after cleaning, cannot boot known-good diskettes is likely to
have screwed-up heads. However, it's a good idea to try unplugging and re-plugging the
drive (with the computer OFF) and, then, try another boot.
If you have a 5.25" drive attached, boot ProDOS from the 5.25" drive and try some
CAT's of non-protected known good 3.5" diskettes in the 3.5" drive. As earlier, do the
cable wiggling test while attempting the CAT's.
A very good test is to try out the drive on a friend's IIgs or IIc+. If it
continues to bomb, it is likely to have R/W heads which have become badly misaligned,
heads which are badly worn, or heads which have been partially dislodged from the
mountings. (The 3.5" drive's heads are held in place by springy metal sheets. Unlike
the mounting for the 5.25" Disk ][ head, these are fairly delicate. If anyone has
tried cleaning the heads by sticking in an alcohol swab and 'swishing around', there
is a good c
hance the head mountings are messed up.)
Shops which replace heads are fairly rare. I had this done a few years ago and
the drive still works fine. However the charge is around $80. It is cheaper and easier
to get a good 2nd-hand drive at a swap-meet. You can, also, look for a bargain Mac
drive and do a "transplant" as described by Steve Buggie in the Winter 1996 issue of
II Alive.
Steve Buggie is a good source of information on drive repairs. Check out some of
his recent posts to this newsgroup.
----------------------
010- Sometimes the 3.5" drives on my GS do not function correctly.
This started after adding a SCSI interface card.
Is there a fix?
This problem seems to crop up from time to time, especially when a SCSI interface
is present and when no device is connected and recognized on the SCSI chain. (For
example, you may have only a Zip Drive connected to your SCSI interface; but, it is
not powered ON or no Zip disk is inserted.)
Evidently, something (e.g. a register or softswitch) involved in the usual GS
power-up routine relating to on-line devices gets messed up. Arranging to have some
active, on-line device on the SCSI chain (or removing the SCSI card) seems to help
reduce frequency of the problem.
A nearly certain fix is inserting a 3.5" diskette into Drive 1 before or just
after power-up. This usually forces recognition of 3.5" diskette drives and enables
correct functioning.
----------------------------
011- Both of my Disk ]['s come on when booting! How can I fix this?
Basically, it sounds like Drive 2 does not know when to stay OFF. There are three
fairly high-probability places where a glitch may cause this to happen:
1. The 74LS132 on the Disk ][ Controller card may have a blown gate or some pins may
be making poor or no contact. Try unplugging and re-socketing the IC. This usually
takes care of bad contact problems. (Or, you can replace the 74LS132 IC with another
74LS132 or 74132. A 74LS00 or 7400 may work, too.) Also unplug and re-socket the 9334
and 556.
2. The ULN2003 IC on the Drive 2 main circuit board may have a bad gate or may have
developed some poor pin-to-socket contacts. Remove the drive cover. Unplug and
re-socket the ULN2003 IC. (Replacing a blown ULN2003 should not be too difficult. Both
Mouser and Newark carry the IC.)
3. Drive 2's cable may have developed a short between pins 14 and 16. Mark the
position of the cable at the Controller card and at the Drive 2 circuit board and
unplug the cable at each end. Use an Ohm meter to check for shorts between adjacent
pins. If you find a short between 14 and any other pin you can try repairing the cable
or cutting out line 14 and running a new lead; or you can get a replacement cable.
___________________________
From: Rubywand
012- In connecting a second Disk II drive to my Disk II card I
misaligned the connectors. The result upon turning it on was a
static-like clicking noise. Now I can't load anything from
disk. Is the Disk II card dead? Are the IIe and Drives all
right?
Try removing the drive which was connected incorrectly. If your system boots from
the remaining drive (connected in the Drive One position), this is a fairly good
indication that the Disk II card and IIe are okay and that the removed drive is messed
up.
If it looks like a drive is bad, remove the cover and inspect the drive's main
circuit board for blown components. If nothing obvious shows up, a decent fix try is
to replace the 74LS125 IC on the drive's main circuit board. (Also, see Q&A 013.)
----------------------------
From: Ryan Underwood
I accidentally offset a row of pins on the //e disk controller card when plugging
one of the drives in. Snap, crackle... you get the picture. I opened up my freshly
fried Disk II, and in the center of the board there is a 74LS125 that is blown.
Replaced it (it was socketed) with the same chip from another Disk II, and voila! it
works again.
I would reasonably assume that misaligning the drive connector on the controller
is what blew the 74LS125 in several Apple II drives before they got to me. Note that
while the genuine Apple Disk II simply lights the LED and doesn't move the head at all
when this IC was blown, a Mitac drive actually ate disks. So any number of dead Apple
II drives with different symptoms could have a blown 74LS125.
___________________________
From: Rubywand
013- Last night a sound like a shotgun going off came from my 5.25"
Disk ][ drive. Now it doesn't work. How can I fix it?
The noise was probably an electrolytic capacitor exploding. Sometimes, these
develop internal shorts, heat up, and blow (kind of like a sealed can of beans on a
campfire).
The fix is to remove the drive cover and replace the blown capacitor. (Look for a
small can-like component with goo and/or shredded foil coming from it.) Circuit board
markings should help identify the component. Here are some suggested replacement
values:
C2 (on +12V line): 220uF-500uF at 20V-50V
C4 (on +5V line): 470uF-500uF at 10V-25V
C5 (on -12V line): 10uF-50uF at 20V-50V
If there is some difficulty identifying the blown capacitor, replace it with a
500uF unit rated at 20V-50V.
Before removing the bad capacitor, note which lead is connected to the outside
'can' part and mark the circuit board where this lead is connected. This is the
Negative side of the capacitor. When installing the new capacitor make sure its
negative lead goes to the marked point on the circuit board.
____________________________
From: Wayne Stewart
014- Recently I picked up two 3.5" drives at a swap meet-- a
Uni-disk and a Laser 128 drive. I've tried cleaning the
heads; but, neither works with my IIc. What's the problem?
The 3.5 unidisk won't work on the earlier IIc unless the IIc has had a ROM
upgrade. The Laser 3.5 is actually a Macintosh drive with the addition of an eject
button. It isn't compatible with any Apple II unless it has a special controller card,
which of course a IIc doesn't.
____________________________
From: Stephen Buggie
015- Can I replace a bombed Apple II 3.5" drive mechanism with
one from a Mac?
Yes. 3.5" drive mechanisms are cheaply and abundantly available from the
Macintosh world. Although Apple II users have increased their interest in 3.5" drives,
these drives have declined in their utility for Mac users who have shifted to hard
drives, CD-ROM, and flopticals. Few Mac owners have use for the external 3.5" drive
any more; if they have not yet discarded their external 3.5" drive, it is now in
storage.
MAC AND APPLE II 3.5" DRIVES: SIMILARITIES/DIFFERENCES
The basic Sony 3.5" mechanism is shared by Mac and Apple II. It stores 800K of
data on a two-sided disk. Unlike the IBM version with its constant rotational speed,
Mac/Apple II drives maintain constant head velocity by varying the rotational speed as
the head assembly approaches towards or moves away from the disk hub. Mac and Apple
II drives differ in their track sectoring arrangements, so disks cannot be read
directly without special translational software. The opportunity for compatible disk
sh
aring was lost during development, because rival teams working on Mac/Apple II drives
went their separate ways (Steve Weyhrich, APPLE II HISTORY, Pt. 9, 1992).
The platinum 3.5" drive supplied with the IIgs is directly compatible with the
Mac, although the Mac ignores its front panel manual eject button; Mac disk ejection
is handled strictly by the desktop trash icon command. An older version of the
external Mac 3.5" drive lacks the manual eject button and, in its casing, is
plug-incompatible with Apple II. Thanks to advice provided by Ken Watanabe, I learned
that the inner mechanism is identical among all versions of 800K Mac and Apple II
drives, includi
ng the internal drive mechanism in the Mac CPU. This is good news for Apple II users
who wish to transplant the abundantly available Mac mechanism into their platinum 3.5"
drive casing.
WHAT ABOUT THE APPLE UNIDISK 3.5" DRIVE?
The classic white Unidisk drive was released in 1985 as a 3.5" platform for the
IIe and IIc. This release date was 18 months prior to the introduction of the IIgs.
Disks written by the Unidisk 3.5 and Platinum 3.5 drives are fully interchangeable;
the two models differed because the earlier Unidisk 3.5 used an intelligent
microprocessor-controlled analog board to slow the data transfer rate to match the
IIe/IIc parameters. This slowdown was not needed for the popular platinum 3.5 drive
used by the
IIgs.
Can the Mac mechanism be transplanted to the Unidisk 3.5 casing? Probably yes,
but this has not yet been verified. I am reluctant tohack with the working Unidisk
3.5's attached to my IIC's. I now seek a mechanically jammed Unidisk 3.5 drive to
verify whether its life can be resurrected with a Mac transplant.
FINDING A USED MAC 3.5" DRIVE MECHANISM
The internall DSDD 800k drive mechanism can be salvaged from any mid-vintage Mac
except for early models (Mac 128, Fat Mac 512) ---- those two models used a quaint
single-sided 400k drive. Suitable models include the Mac Plus, Mac SE, Mac II, or
other Macs that have the standard DSDD 800K mechanism --- newer Macs have incompatible
high density drives. Get a genuine Mac Sony drive mechanism, not a clone; the
suitability of non-Sony clones is uncertain.
Salvaged internal drives must be removed from the Mac internal mounting bracket
--- take out the four side-mounted bolts, and slide the mechanism forward. The early
version of the external Mac mechanism is mounted in a plastic casing that resembles
the Apple II platinum drive except that the manual eject button is absent.
Remove the mechanism from the casing, but save its round external cable and db-19
plug --- that cable/plug can be used later to adapt flat-ribbon Apple II drives for
use with the IIgs or IIIc! The Mac externaldrive's plastic casing can be saved for
use as a coin bank, or discarded.
You should anticipate that the older Mac drive has had plenty of use; most Mac
users have fewer drives attached to their computer than is common for the Apple II.
The 3.5" drives are sturdier than hard drives, but to protect the drive's head
assembly from damage during rough shipment, the seller should be asked to ship the
unit with a disk inserted.
DISASSEMBLY OF THE APPLE 3.5" PLATINUM DRIVE
Use a well-light work area that gives you plenty of elbow room, with containers
to hold bolts and other small parts All dimensions (left/right/top/bottom/front/rear)
refer to the unit's own dimensions, NOT to your own egocentric viewpoint as the
observer. Standard precautions against static or other electrical damage must be
followed: Discharge static frequently by touching grounded metal, wear a grounded
wrist strap, hand all power OFF when attaching/removing drives, put insulating tape
over the d
b-19 drive plug when not in use.
Move slowly and patiently when removing or inserting the mechanism from its
housing ---- metal parts must not be forced or bent. These tools areneeded: (a)
medium and small Phillips-head screwdrivers, (b) a small pliers, and (c) a fine-tipped
felt marker. This procedure was outlined in an essay by Lorne Walton (Apples BC,
1992), but many further details have been added here to facilitate disassembly and
drive replacement.
The first step is to remove the worn/defective mechanism from its Apple II
platinum casing. Flip the casing on its back and rest it on soft cloth. Re,ove the
four shiny bolts from the bottom of the casing. With the unit inverted, slowly lift
the bottom half-shell of the plastic casing upward and push the external cable's
attached grommet towards the upper casing. The unit's bottom casing should come off
cleany.
Use the felt marker to label the unit's own main dimensions, writing on the metal
internal shroud: front-bottom, rear-bottom, left side, right side. Examine the metal
innards as they lie upside down in the upper casing. Note that a red and black wire
pair are tucked on the inner edge of each side --- These two wires go to the eject
switch (right front) and to the red in-use LED lamp (left front).
At the unit's rear, observe that the wire pairs terminate in RED and BLACK plugs.
Use the felt-tipped marker to write "R" and "B" on nearby metal surfaces to
identifythe positions of these two plugs. These letters will help during reassembly
when reinsterting the two plugs onto their proper pins. Next, use the small pliers to
grasp each plug, slowly and carefully pulling it backwards to remove it from its
mounting pins.
With the black and red plugs each removed, slide the top plastic cover in a
rear-to-front direction, past the metal-enshrouded mechanism. The wire-pairs from the
eject-button and also from the in-use LED lamp should remain tucked into their plastic
side-braces.
You now hold the mechanism, enshrouded in its grey metal shielding, with the
external db-19 cable protruding from the rear. Remove the two medium Phillips mounting
bolts (with flat washers) from each side. Remove the single medium Phillips
bolt/washer that is centered on the upper-rear metal shroud. Then lift off the
upper-rear should and look inside.
Note that the round external cable terminates in a familiar IDE-20 flat-ribbon
connector that plugs into the inner mechanism. Unplug that inner connector --- the
small pliers can be used to rock and pull the connector towards the rear. With the
IDE-20ribbon connector unplugged, the inner mechanism can be slid forward and out.
As you hold the inner mechanism in your hand, observe that a shiny thin metal
shroud covers its to and sides. Use the felt-tipped pen to label this shrou's
dimension: TOP-FRONT and TOP-REAR. This thin shroud should be removed by rocking it
and spreading its thin side-tabs. At this point, you have the bare mechanism in your
hand, with heads visible from its top perspective, and with pancake motor visible
underneath.
You are now ready to begin reassembly, but pause to appreciate what is before
you. Hold the old mechanism and its Mac replacement side-by-side --- they should
appear identical. The date of manufacture is coded on a sticker on the pancake motor
(e.g., 8809 = September 1989). Apply rubbing alcohol with a cotton swab to clean the
surfaces of both read/write heads.
REASSEMBLY
Remount the innermost top-and-sides metal shroud, taking care that its "fingers"
have clicked into place on the mechanism's sides. When properly fited, both bolt-holes
on each side will be visible through the shroud's thin metal. If the shroud does not
fit, or if the bolt-holes are not seen, check with your dimensional labels to verify
that the front and rear have not been reversed.
With the top/side inner shroud correctly in place, then reverse the disassembly
steps: Slide the mechanism through the front of the metal shroud. Reattach the IDE-20
internal ribbon connector, align the two bolt holes on each side of the outer shroud
with the mechanism and reinstall the four medium Phillips bolts and their washers.
Then reattach the rear-upper shroud with its centered bolt and washer. Reassembly of
the outer metal shroud is now finished!
The final reassembly task is to refit the enshrouded mechanism into the plastic
outer casing. Lay the inverted UPPER plastic half-shell on the bench,with its front
facing away from you.
Observe the small red or black wires tucked along the sides of the upper plastic
half-shell. With the metal enshrouded drive mechanism upside down, it should be slid
into the plastic top-shell, from its rear to its front. Check that the red-black
wires remain tucked along the inner edge between the plastic casing and the metal
shroud. Insert the black and red plugs into their respective connectors. Note the
"R" and "B" markings you wrote on the metal shroud; those markings will guide the
plugs' in
sertion into their proper connectors.
The oblong-shaped grommet attached to the round external cable should be fitted
first to the bottom plastic half-shell casing, which is then mated to the top casing.
Reattach the four small shiny Phillips bolts through the bottom plastic half-shell,
and you're done!
____________________________
From: David Empson
016- I have one 5.25" drive connected to my GS, but the System 6.0.1
Finder display shows two 5.25" icons!? How can I fix this?
You need to change the AppleDisk5.25 driver file's auxilary filetype from $010E
to $0101. You can use File Manager (an NDA utility) to make the change.
For a standard GS/OS device driver, the lower six bits specify the number of
devices supported by the driver (see the file type note on GS/OS drivers:
FTN.BB.XXXX), so the maximum number of devices that can be supported by a single
driver is 63. You should NEVER increase this higher than the original value, because
the driver probably doesn't have space in its device tables to support more drivers
than it originally claimed to.
The AppleDisk5.25 driver supports a maximum of 14 devices - two 5.25" drives for
each available slot. (In theory, it should be able to support 16: all seven real
slots, plus the built-in disk port, but Apple never completed the implementation of
dynamic slot switching for drivers, probably for compatibility reasons.)
Don't change any of the higher order bits. The high order byte specifies the
type of driver ($01 = GS/OS device driver), and the top two bits of the low order byte
specify the type of GS/OS driver (00 = standard).
NOTE: All of the above applies ONLY to GS/OS standard device drivers, not to GS/OS
supervisory drivers, printer drivers, or anything else. See the filetype note for
further information.
There is one bit in the auxiliary type which is the same for all types of
drivers: bit 15 set ($8000) indicates the driver is inactive (this is what Finder
toggles when you click on the "Inactive" check box).
____________________________
From: Neil Parker
017- How does one distinguish between a 13 and 16-sector Disk ][
controller card?
For a while at least, new 16-sector Disk II cards shipped with a little white
circular sticker depicting a red Apple with the number "16" in the middle.
But the sticker is hardly a reliable test. A better test is to look look at the
part numbers of the P5 PROM (the lower left chip on the card) and the P6 PROM (left
column, second from the top).
13-sector 16-sector
--------- ---------
P5 341-0009-xx 341-0027-xx
P6 341-0010-xx 341-0028-xx
The 16-sector PROMs may also be labelled "P5A" and "P6A".
A program can test the card type by looking at its slot ROM space. The signature
bytes are as follows:
$Cn01: 20
$Cn03: 00
$Cn05: 03
$Cn07: 3C
$CnFF: FF if 13-sector; 00 if 16-sector
For example,
1 REM Scan the slots for Disk II interfaces
2 REM By Neil Parker
10 FOR S = 1 TO 7
20 A = 49152 + 256 * S
30 IF PEEK (A + 1) < > 32 OR PEEK (A + 3) < > 0 OR
PEEK (A + 5) < > 3 OR PEEK (A + 7) < > 60 THEN 100
40 PRINT "Disk II (";
50 T = PEEK (A + 255)
60 IF T = 0 THEN PRINT "16-sector";: GOTO 90
70 IF T = 255 THEN PRINT "13-sector";: GOTO 90
80 PRINT "other";
90 PRINT ") in slot "S
100 NEXT
____________________________
From: Dan DeMaggio
018- Can a Disk ][ Drive be used on a IIc or GS smartport?
Yes. Call Jameco Electronics. Get the S20-pin header- to -DB19-pin connector
module. It is intended for adapting II/II+ drives for IIc. (Part# 10022; Product name:
AAM APPLE IIC ADAPTER; price: $3.95)
____________________________
From: Rubywand
019- I would like to add a Read/Write indicator to my Disk ][
drive. How can I do this with a bi-color LED?
The circuit described below works well. It shows Red for Drive Enabled + Write
and Green for Drive Enabled + not Write. That is, a Read is assumed if the drive is ON
and no Write is occurring. The advantage of this approach is that you always have a
lighted LED 'drive ON' indicator and, so, there is no need to drill a new hole in your
drive panel. The new LED can use the hole occupied by the old "in Use" indicator LED.
Parts
IC- 74121 or 74LS121 1-Shot multi-vibrator
Qgreen- 2N2222A gen purpose NPN transistor
Qred- 2N2222A gen purpose NPN transistor
Rcath- 120 Ohm 5% 1/4 watt resistor
Rgreen- 3.3k 5% 1/8 watt resistor
Rred- 3.3k 5% 1/8 watt resistor
Rp- 20k 5% 1/8 watt resistor
Cp- 10uF/10v 10% "dipped tantalum" capacitor
LED- 2.2V 20ma 3-lead (common cathode) Green/Red bi-color LED
Building the Circuit
IC- locate pin-1 and mark it on bottom side with white-out.
'Dead-bug' mount the IC using epoxy in the open area near
top-middle of board with pin-1 end pointing to the right.
connect Rcath to solder pad at - (minus) end of C2
connect #20 wire from IC pin-7 to solder pat at - end of C2
connect Rp from IC pin-11 to IC pin-14
connect Cp + to IC pin-10 and Cp - to IC pin-11
connect #20 wire from IC pin-14 to solder pat at + end of C4
connect a wire from IC pin-3 to end of R16 closest to 74LS125
connect Rgreen to IC pin-1 (74121 "/Q" output)
connect Rred to IC pin-6 (74121 "Q" output)
solder transistor Qred Collector to Q1 power transistor Collector
(solder pad area at left front of circuit board just to left of
the power transistor). Position toward left edge of pad.
solder transistor Qgreen Collector to Q1 power transistor Collector
solder pad to the right of Qred.
LED- connect a 3-wire 11" cable to the LED (black to center, red to
to lead with right-angle bend, green to lead with slant bend).
Old "in Use" LED- pop off the retainer ring and push through the
LED. Leave the LED mount in the hole. Cut off the LED, spread
cable ends and tab over with cellophane tape. (Put old LED and
ring into parts box.
Spread apart retainer 'leaves' of LED mount (at back side of panel)
to permit easier insertion of new 3-lead LED.
Run LED + cable over back of board and along bottom toward the
hole in the front panel. Push through hole. (If hole is too small,
use a Dremel tool and steel 'bulb bit' to slightly enlarge front
part of hole.)
connect LED cable black to free end of Rcath
connect LED cable green to Emitter of Qgreen (right transistor)
connect LED cable red to Emitter of Qred.
position old LED cable beneath new LED cable.
connect a wire from the free end or Rgreen (on IC pin-1) to the
Base lead of transistor Qgreen.
connect a wire from the free end or Rred (on IC pin-6) to the
Base lead of transistor Qred.
Add epoxy to the back of the LED and holder to secure the LED.
How it Works
When /Enable goes low to select the Drive, the power transistor (Q1) switches ON
and supplies +12V at its Collector. If there is no Write, 74121 output /Q is high,
Qgreen conducts, and the LED shows Green. That is: the Green LED will light during
boots and for any READs.
If the Drive is selected (/Enabled is low) and there is a Write operation and
Write Protect is not ON, then, the /Write Request signal at 74LS125 pin 8 will go low.
This triggers the 74121 One-Shot (at pin 3) producing an aprox. 160ms pulse at 74121
output Q. For the duration of the pulse, /Q is low and Q is high. Qred conducts, and
the LED shows RED to indicate WRITE.
____________________________
From: Dan DeMaggio
020- What's the scoop on the 3.5" High Density drive?
In order to do High Density on the Apple II, you will need both the High Density
3.5" drive and the Apple 3.5" HD controller. If you don't have both, you will only be
able to do regular density. Of course, you will also need High Density diskettes.
Once you have collected the above items, you are in for a pleasant surprise.
ProDos 8 programs not only recognize it, but most programs format and recognize HD
disks just fine. You can even boot off of a HD disk, allowing plenty of room for
System Desk Accessories and such.
There are a few drawbacks: You cannot boot copy-protected software or some FTA
demos. You can't daisy-chain a 5.25" on an HD card. Also, it takes up a slot, even on
the GS.
____________________________
From: Benjamin Summers
021- What is a "UniDisk"?
The UniDisk 5.25 was Apple's replacement for the venerable Disk ][. It featured
an updated design, tan color plastic case, a DB-19 cable, and daisy-chain port on the
back to which other drives could be connected. The case color was later changed to
platinum and the drive was rechristened to the "Apple 5.25 Drive".
The UniDisk 3.5 was Apple's first 3.5" drive for the Apple II line. Like the
Unidisk 5.25, it had the DB-19 cable and daisy chain port on back. UniDisk 3.5 was
dropped in favor of the Apple Disk 3.5, a different design, at the time of the launch
of the IIgs.
----------------------------------
From: Mitchell Spector
One important difference you forgot to mention: The UniDisk 3.5 was an
"intelligent" drive, whereas the Apple 3.5 was a "dumb" drive. There was a specialized
circuit board inside the UniDisk 3.5 drive which had its own processor, memory, IWM
controller and firmware. This was needed for the //c, in order for the drive to
process data before sending it on to the machine (which was too slow to do the job by
itself). You can easily spot a UniDisk 3.5 as it matched the snow-white color of the
//c and had i
ts access LED and eject button _above_ the disk insert slot (the Apple 3.5 has them
in-line).
____________________________
From: Rubywand
022- What is a "RAM disk"; and, how do I create one on my IIgs?
A RAM disk is a block of memory which your computer uses like a disk.
To create a RAM disk on your IIgs ...
o- Boot a ProDOS-8 or DOS 3.3 diskette; or, start your computer with no boot and press
CONTROL-Reset to get to the Applesoft prompt.
o- Press OpenApple-Control-ESC (all three keys at once) to get to the Desk Accessories
menu and select "Control Panel".
o- In the Control Panel menu, select "RAM Disk".
o- Set "Minimum RAM Disk Size" and "Maximum RAM Disk Size" to the the same value =
size of the RAM disk you want. If you have enough RAM left over to start your
operating system and run your favorite application, a good RAM disk size is 800k.
o- Press Return to set the value. Exit the Control Panel. Exit the Desk Accessories
menu. Turn OFF the computer.
When you next power up your computer, your RAM disk will be ready to use.
____________________________
From: David Empson
023- Which 3.5" drive/interface combinations work on a IIe?
For the UniDisk 3.5 (model number A2M2053), you need either Apple's "SuperDrive"
card or the "Liron" card. The UniDisk 3.5 is quite rare. It is a clean white color
instead of greyish "platinum". It also has the eject button just above the line of the
disk insertion slot, with a separate manual ejection hole.
The "Liron" card's official name is "Apple 3.5 Floppy Disk Drive Interface Card".
It has the word "Liron" on the back (which is the nickname of the IWM disk controller
chip, if I remember right).
For the Apple 3.5 Drive (model A9M0106 as used on the IIgs), you need either
Apple's "SuperDrive" card or the third party "Universal Disk Controller" card. The
drive is platinum in color and has the eject button in line with the disk insertion
slot and the ejection hole is in the middle of the button.
The "SuperDrive" card's official name is "Apple II 3.5 Disk Controller Card". The
card has an LED on top, and has its own processor, RAM and ROM.
For the Apple SuperDrive, you need the "SuperDrive" card. Model ID is
inconsistent. Check for something like "Family number G7287".
The SuperDrive looks exactly the same as the Apple 3.5 Drive. It supports 1.44 MB
high density and 720 KB double density disks as well as the 400 KB and 800 KB formats.
You can use a SuperDrive with the Universal Disk Controller card, but you won't be
able to use its extra capabilities, and it will behave like an Apple 3.5 Drive.
____________________________
From: O Aaland and Michael Pender
024- How can I boot from my /RAM5 RAM disk? All the files are there
but it just beeps at me and says 'check startup device'!?
For the RAM disk to be bootable, you need to do a whole-disk copy of a same-size
bootable diskette to the RAM disk. Or, you can initialize* the RAM disk before you
copy files to it or do an install.
*Note: To initialize the RAM disk, click on the RAM disk icon to select it. Then,
click on "Disk" on the menu bar and select "Initialize". Follow the prompts to init
the disk.
Finally, in the IIgs Control Panel, go to Slots and set Startup Slot to "RAM
Disk".
____________________________
From: Ryan Underwood
025- My 5.25" drive ruins every disk I insert. How can I fix it?
Probably, the drive's Write signal is ON when it shouldn't be. This happens with
some 5.25" drives when a 74LS125 IC on the drive's circuit board is blown. (I
accidentally offset a row of pins on the //e disk controller card when plugging in a
drive and blew the IC.) I removed the drive cover and replaced the 74LS125-- it was
socketed-- voila! it worked again. (For possible disk-trashing fix for DuoDisk drives,
see Q&A 006.)
| <-- __Chronological__ --> | <-- __Thread__ --> |
